selection and use of adhesive backed mounts and devices
2 panduit offers high performance adhesive backed mounts and devices for a quick, dependable method of securing, routing and protecting wires or cables. the adhesive backing provides easy installation and is an alternative to mechanical fasteners. when properly installed, panduit ? adhesive backed mounts and devices offer the advantage of lower installed cost and high reliability. selection of adhesive choose from three types of adhesive systems designed for specific application environments and temperatures: rubber-based adhes ive foam tape, acrylic-based adhesive foam tape, or two-part epoxy adhesive. carefully choosing the correct adhesive and closely fo llowing the recommended installation steps will provide a reliable, long-term bond. rubber-based adhesive foam tape rubber-based adhesive foam tape is the best choice for the vast majority of adhesive mount applications, including applications where powder coated surfaces are being used. this pressure sensitive tape develops its strength extremely fast and can be used in ind oor environments with temperatures ranging from -20f to 120f (-29c to 49c). rubber-based adhesive foam tape is the most widely used and generally recommended foam tape for wire routing applications. acrylic-based adhesive foam tape acrylic-based adhesive foam tape is a good choice in applications with prolonged exposure to uv rays or heavy moisture. it is d esigned to be used in indoor or outdoor environments where temperatures can vary from -20f to 180f (-29c to 82c). the acrylic-based adhesive develops its maximum strength over a longer period of time compared to the rubber-based adhesive. it is recommended that the mounts dwell eight (8) hours after installation and prior to loading. two-part epoxy adhesive two-part epoxy adhesive is for use in applications where excessive loading is required or where the mounting surface is porous rather than smooth. this adhesive is formulated specifically for use on panduit ? ems and asms mounts in either indoor or outdoor applications. it is packaged in convenient pre-measured cups to insure the proper ratio of resin and hardener, as well as elimi nate waste. panduit ? adhesive backed mounts and devices features and benefits superior adhesive for long term reliability 2-up mount configuration speeds liner removal and installation 4-way cable tie entry makes part orientation fast and easy adhesive backing allows routing of wires and cables where mounting holes cannot be drilled mount sizes range from .50" x .50" to 2.00" x 2.00" for space limited or heavy load applications ul recognized used with panduit ? cable ties for a complete wire routing solution one piece solutions lower inventory costs and speed installation cable tie entry ramps guide the cable tie into the mount bevel entry on wire clips speeds installation releasable latches allow addition or removal of cables
3 guideline for adhesive the following chart should be used as a guideline for choosing the best adhesive for common surfaces and chemical resistance. since each application has specific requirements, panduit recommends that further testing be conducted to determine the suitability of the adhesive in a specific environment or application. 1. not recommended for use on copper or brass. 2. mounts manufactured from outdoor material only. for specific applications, individual testing prior to extensive use is sugges ted. 3. depends on concentration, exposure time and chemical composition. surfaces plastics good good good wood good good good glass fair good good painted surfaces good good fair powder coating good fair good metal good 1 good 1 good paper good good fair concrete, stone, masonry not recommended not recommended good chemical resistance water good poor poor oil poor fair 3 good gasoline poor fair 3 fair dilute acids poor fair 3 fair dilute alkalis good fair 3 fair organic solvents poor fair 3 not recommended outdoor exposure not recommended good 2 good 2 rubber based foam tape mounts acrylic based foam tape mounts epoxy applied adhesive mounts
4 proper installation steps surface preparation for best results, mounts should be applied to a clean, dry, and grease-free surface. it is recommended that for each individual application, a solvent or cleanser be used to thoroughly prepare the surface for mount installation. the following are recommended cleaning guidelines: 1. for rubber and acrylic-based adhesive foam tape, a mixture of water and isopropyl alcohol may be used on most surfaces. for two-part epoxy adhesive, especially on masonry surfaces, be sure to clean all loose particles away before mount installation. some surface abrasion is recommended on smooth surfaces to achieve maximum strength. a light rubbing with medium grit emery cloth or sandpaper is best. wash the surface after abrading. 2. allow the surface to dry completely before applying the mount. 1. for proper installation of adhesive backed mounts with foam tape, remove the release liner from the foam adhesive. without touching the adhesive, place the mount in the desired location. for two-part epoxy adhesive mounts, apply 1/3 of the mixed adhesive to the bottom of the panduit ? ems or asms mount. without touching the adhesive, place the mount in the desired location. 2. apply firm pressure for five (5) seconds to the foam tape mounts to insure proper adhesion. two-part epoxy adhesive mounts should be twisted in place to ensure the adhesive is forced into the porous surface. 3. allow the mount to remain in place for the recommended dwell time for the specific adhesive being used. the dwell time for rubber-based adhesive foam tape is two (2) hours and for acrylic-based adhesive foam tape it is eight (8) hours. two-part epoxy adhesive mounts can support about 5 lbs. after first fifteen (15) minutes. the adhesive fully cures after twenty-four (24) hours and bonding strength will exceed 50 lbs. 4. the mount is now ready to be used. installing the mount alcohol 12 6 3 9
5 mount spacing to determine the number of mounts to use in a given application, the following formula can be used as a guideline: for example, to determine the mount spacing using part number abm2s-a-c for an application with a bundle of wires that weigh on e pound per foot, the formula would be: proper storage conditions mounts and adhesives should be kept in the original packaging until they are ready to be applied. store at room temperature 70 f (21c) with 45% or less relative humidity. avoid storing adhesive products near heating vents or other heating sources. using the guidelines above, the average shelf life of adhesive foam tape is three (3) years from the date of manufacture. the s helf life of two-part epoxy adhesive is one (1) year from the date of manufacture. failing to follow the recommended storage conditions may reduce the shelf life or adhesive strength of the foam tape and two-part epoxy adhesive. adhesive technical information adhesive foam tape properties are developed with thorough laboratory research and testing. the double-coated adhesive foam tape used on panduit ? adhesive backed mounts is manufactured under strict quality requirements, which provide consistent, high quality performance for use on adhesive mounts. each package of mounts has an expiration date and a quality control number printed on t he label, which permit traceability. double coated foam tape properties polyethylene (in.) total less liner 6 .040 .035 polyethylene 6 .039 .034 rubber adhesive acrylic adhesive cable bundle weight in lbs/foot minimum number of mounts per foot = maximum static load rating of the mount* 1 pound per foot 0.5 lbs load rating 2 mounts per foot = * see pages 6-7 for static load ratings. backing material nominal backing density (pcf) thickness (pstc-33) static shear mil-t-60394a (hours) 72f/17.6 psi 72f/8.8 psi 158f/2.s psi 500+ 1000+ 100+ n/a n/a 200+
6 abm abmt pla sms ajc a2c macc lwc adhesive backed mounts and clips part number material length width max. static load adhesive type std. pkg. qty.? in. mm in. mm lbs. g 4-way adhesive backed mounts abm1m-a-c nylon 6.6 .50 12.7 .50 12.7 .13 59 rubber 100 abmm-a-c abs .75 19.1 .75 19.1 .30 136 rubber 100 abm2s-a-c abs 1.00 25.4 1.00 25.4 .50 227 rubber 100 abm100-a-c nylon 6.6 1.00 25.4 1.00 25.4 .50 227 rubber 100 abm112-a-c nylon 6.6 1.12 28.6 1.12 28.6 .63 286 rubber 100 abm3h-a-l nylon 6.6 1.50 38.1 1.50 38.1 1.12 508 rubber 50 abm4h-a-l nylon 6.6 2.00 50.8 2.00 50.8 2.00 907 rubber 50 t ak -t y ? hook & loop cable tie mounts abmt-a-c nylon 6.6 1.10 28.7 1.10 28.6 .38 174 rubber 100 abmt-a-c20 nylon 6.6 1.10 28.7 1.10 28.6 .38 174 rubber 100 combination adhesive mount/cable ties pla2s-a-q nylon 6.6 1.00 25.4 .90 22.9 .45 204 rubber 25 pra2s-a-q nylon 6.6 1.00 25.4 .90 22.9 .45 204 rubber 25 snap-in cable tie mount sms-a-c abs 2.00 50.8 1.00 25.4 1.00 454 rubber 100 c lincher ? adjustable releasable clamp arc.68-a-q polypropylene 1.00 25.4 1.00 25.4 .50 227 rubber 25 adhesive backed cord clips acc19-a-c nylon 6.6 .63 16.0 .76 19.3 .20 91 rubber 100 acc38-a-c nylon 6.6 1.00 25.4 1.00 25.4 .50 227 rubber 100 acc62-a-c nylon 6.6 1.25 31.7 1.12 28.6 .70 318 rubber 100 ?j? clips ajc12-a-c pvc 1.00 25.4 .86 21.8 .40 182 rubber 100 ajc19-a-c pvc 1.25 31.8 .89 22.6 .50 227 rubber 100 ajc31-a-c pvc 1.75 44.5 1.23 31.2 .90 408 rubber 100 ajc38-a-c pvc 2.00 50.8 1.28 32.5 1.00 454 rubber 100 a1c type clips a1c12-a-c8 pvc .77 19.6 .63 16.0 .14 64 rubber 100 a1c25-a-c8 pvc .91 23.1 .63 16.0 .14 64 rubber 100 a1c38-a-c8 pvc 1.04 26.4 .63 16.0 .14 64 rubber 100 a1c50-a-c8 pvc 1.17 29.7 .63 16.0 .14 64 rubber 100 a2c type clips a2c12-a-c8 pvc 1.30 33.0 .63 16.0 .14 64 rubber 100 a2c25-a-c8 pvc 1.43 36.3 .63 16.0 .14 64 rubber 100 a2c38-a-c8 pvc 1.56 39.6 .63 16.0 .14 64 rubber 100 a2c50-a-c8 pvc 1.68 42.7 .63 16.0 .14 64 rubber 100 metal adhesive backed cord clips macc25-a-c zinc plated steel .79 20.0 .53 13.5 .21 95 rubber 100 macc62-a-c zinc plated steel 1.18 30.0 .75 19.1 .44 200 rubber 100 latching wire clips lwc19-a-c nylon 6.6 .85 21.6 .61 15.5 .25 113 rubber 100 lwc25-a-c nylon 6.6 .88 22.2 1.00 25.4 .45 204 rubber 100 lwc38-a-c nylon 6.6 1.00 25.4 1.00 25.4 .50 227 rubber 100 lwc50-a-l nylon 6.6 1.26 32.0 1.00 25.4 .63 272 rubber 50 lwc75-a-l nylon 6.6 1.48 37.6 1.24 31.5 .93 417 rubber 50 lwc100-a-l nylon 6.6 2.21 56.1 1.97 50.0 2.25 1020 rubber 50 arc acc a1c contact customer service (800-777-3300) for additional sizes, materials, and acrylic tape availability or visit www.panduit.com . ? order the number of pieces required, in multiples of standard package quantity.
7 part number color environment used with cable ties number of cable ties number of ems mounts number of epoxy cups number of mixer sticks std. pkg. qty.? epoxy adhesive only ema-x gray indoors/outdoors ?? ? ? 10 10 10 epoxy mounting kit with ems mounts emsk3-1-x0 black indoors/outdoors m, i, s ? 3 1 1 10 epoxy mounting kit with ems mounts and cable ties emsk3-1-3-0 black indoors/outdoors m, i, s 3 plt2s-0 3 1 1 1 emsk12-4-12-x0 black indoors/outdoors m, i, s 3 plt2s-0 12 4 4 10 epoxy applied mount kits epoxy applied mounts adhesive backed mounts and clips (continued) contact customer service (800-777-3300) for additional sizes, materials, and acrylic tape availability or visit www.panduit.com . ? order the number of pieces required, in multiples of standard package quantity. ? order the number of pieces required, in multiples of standard package quantity. g lbs. mm in. mm in. std. pkg. qty.? adhesive type max. static load width length material part number bevel entry clips bec38-a-l nylon 6.6 1.46 37.1 1.24 31.5 .91 411 rubber 50 bec62-a-l nylon 6.6 1.46 37.1 1.24 31.5 .91 411 rubber 50 BEC75-A-L nylon 6.6 1.46 37.1 1.49 37.8 1.09 493 rubber 50 vertical cord clip vcc25-a-c nylon 6.6 1.00 25.4 .50 12.7 .25 113 rubber 100 adhesive backed latching clips lc3-a-c8 pvc .75 19.0 .75 19.0 .28 127 rubber 100 lc5-a-c8 pvc 1.01 25.7 1.00 25.4 .50 227 rubber 100 lc10-a-l8 pvc 1.51 37.9 1.00 25.4 .60 272 rubber 50 low profile flat cable mounts lpfcm14-a-c14 nylon 6.6 2.56 65.0 .50 12.7 .25 113 rubber 100 lpfcm22-a-c14 nylon 6.6 3.31 84.0 .50 12.7 .25 113 rubber 100 lpfcm34-a-c14 nylon 6.6 4.56 115.8 .50 12.7 .25 113 rubber 100 latching flat cable mounts fcm1-a-c14 nylon 6.6 1.21 30.7 1.00 25.4 .50 227 rubber 100 fcm1.2-a-c14 nylon 6.6 1.37 34.8 1.00 25.4 .62 281 rubber 100 fcm2-a-c14 nylon 6.6 2.22 56.3 1.00 25.4 1.00 454 rubber 100 fcm3.25-a-l14 nylon 6.6 3.38 85.9 1.00 25.4 1.50 681 rubber 50 cable holder ? adhesive backed ch105-a-c14 nylon 6.6 2.50 63.0 2.06 52.0 1.28 581 rubber 100 latching flat cable holder fch2-a-c14 nylon 6.6 2.50 63.5 1.03 26.2 1.00 454 rubber 100 flat cable clips fcc-a-c8 pvc 1.00 25.4 1.09 27.7 .50 227 rubber 100 fcc5-a-c8 pvc 1.00 25.4 .56 14.1 .25 113 rubber 100 bec vcc lc lpfcm fcm ch fch2 fcc ems ems kits asms part number material length width max. static load adhesive type std. pkg. qty.? in. mm in. mm lbs. g asms-a-x aluminum base/nylon mount 1.13 28.6 1.13 28.6 10.00 4540 ema epoxy 10 ems-a-c nylon 6.6 1.00 25.4 1.00 25.4 10.00 4540 ema epoxy 100 ? order the number of pieces required, in multiples of standard package quantity.
panduit ? europe ltd. london, uk phone: 44.208.601.7200 panduit ? australia pty. ltd. victoria, australia phone: 61.3.9794.9020 panduit ? asia pacific pte. ltd. republic of singapore phone: 65.6379.6700 panduit ? japan tokyo, japan phone: 81.3.3767.7011 panduit ? latin america jalisco, mexico phone: 52.333.666.2501 panduit ? canada markham, ontario phone: 800.777.3300 panduit ? corp. tinley park, illinois 60477- 3091 for more information or to request a catalog 800-777-3300 cs@panduit.com w w w w w w . . p p a a n n d d u u i i t t . . c c o o m m worldwide subsidiaries and sales offices ? panduit ? corp. all rights reserved printed in the u.s.a. sa-wacb06 04/2004 for a copy of panduit ? product warranties, log on to www.panduit.com/warranty.
|
